***NEW! DUE EARLY JANUARY***
> Send video wirelessly up to 30 metres (98 ft)
> Uses 10 x WiFi Channels – one per transmitter
> Maximum of 2 x receivers per transmitter
> In the same WiFi area create
– up to five discrete 2×2 Matrix systems, or
– up to ten discrete 1:2 Distribution systems, or
– 10:1 switching system, or
– a mix of systems above
Take wireless HDMI one step further; send content from your laptop to one or two flat-panel displays or projectors – even through walls – with ease. No software or drivers necessary. It is plug-and-play, and intuitive.
Each device has a channel selector which scrolls through ten channels. Transmitters (Tx) connect to each source, and each are set to transmit on different channels. Use up to 10 x Tx in the same WiFi area since they all use different channels. Receivers (Rx) connect to the displays. To determine which source they show adjust the channel.
As you plan your system be aware it is not possible for three or more Rx to be on the same channel.
Two sources can be patched to two displays. Set the transmitters to different channels, then adjust the channel on each Rx to switch which source is shown.
Show content from one laptop on two displays. Connect a Tx to the laptop, and a Rx to each display. Set them all to the same channel, and you’re done.
Supports switching up to ten sources on a display. Connect a transmitter (Tx) to each laptop, and a receiver (Rx) to each display. Change the channel on the Rx to determine which source it displays.
When only one display is in use, the Present button on each transmitter can be used to remotely change the channel on the receiver. Note: the switch on the rear must be set to activate this.
Because there are ten channels available you can blend together matrix, distribution, and switching systems
The range can be up to 30 metres (98ft) in an enclosed environment – or up to 50 metres (164ft) in an open space. Too close or too far away and the image will degrade. It uses the same frequencies as wifi so it will work through dry-walls but performance drops off with distance and physical obstacles
It creates it’s own WiFi network in the 5GHz frequency band and uses non-DFS channels to avoid interference. The signal is made secure with 128 bit AES encryption.
As well as using the buttons on the front panel to select channels, an included IR remote control directly selects channels, or a control system can switch them via RS-232.
An onscreen display can be used to look at the frequency spectrum to see what other devices might be interfering with your systems.
It is HDMI 1.3 with HDCP 1.2 compliance. Features not supported are ARC (Audio Return Channel), and Ethernet.
The TC-HDMIWM has a latency of less than 200 millisecond – 1/5 of a second. It can support up to 1080P (1920 x 1080) video and is smooth and glitch-free.
Includes IR blaster and receiver cables to allow control of the source device from the remote display. Supports 20-60KHz frequencies.
If the source is turned off or goes to sleep, the displays associated with that source will also be allowed to sleep.
Other Display Ports
If your computer has Mini-HDMI, miniDisplayPort, DisplayPort, or VGA Vision has all the adaptors you need to make it work. To see them Click here.
TRANSMITTER DIMENSIONS: 135 x 80 x 23 mm / 5.3 ” x 3.1 ” x 0.9 ” (length x width x height)
RECEIVER DIMENSIONS: 135 x 80 x 23 mm / 5.3 ” x 3.1 ” x 0.9 ” (length x width x height)
PACKAGED DIMENSIONS: 200 x 150 x 80 mm / 7.9 ″ x 5.9 ″ x 3.1 ” (length x width x height)
Tx: 290 g / 0.64 lbs
Rx: 290 g / 0.64 lbs
PACKAGED WEIGHT: 630 g / 1.39 lbs (Tx and Rx is separately packaged.)
CONSTRUCTION MATERIAL: Metal
Maximum Video Format Supported: 1920×1080 / 1080P @ 60Hz
Video: HDMI 1.3 with HDCP 1.2
Max transfer rate: 10.2 Gbps
TMDS Signal: 0.5~1.5Vp p
DDC Signal: 5Vp p
IR Passback: 20-60KHz
Max Input and Output cable length: up to 5m (16.4 feet)
Electrostatic Protection: Contact and air discharge level 3 IEC 61000-4-2
Operating Temperature Range: 0-40°C
Operating Humidity Range: < 90 % RH (no condensation)
MTBF (Mean Time Between Failures): > 30,000 hours
Transmitter Power Consumption: Max 5 watts
Receiver Power Consumption: Max 4.5 watts
Latency: < 200 ms
Switch time: up to 7s (allowing for EDID handshake each time)
Maximum distance: 30 m (98 feet)
Encryption: 128 bit AES
LED Channel –> wifi channel –> freq –> bandwidth
1 x HDMI socket – gold-plated input
1 x DC power – phoenix connector
1 x 3.5mm Minijack socket – for IR blaster
1 x HDMI (type A) output
1 x DC Power – phoenix connector
1 x 3.5mm Minijack socket – for IR receiver
1 x 9-Pin D-Sub Male for RS-232
POWER SUPPLY: 100-240v AC 50/60Hz 5 volt / 2 amp 10 watt. DC tail length: 1.8 m / 5.9 ft
Transformer integrated into plug. Includes interchangeable plugs: UK/EU/US/AU. Transformer dimensions: 66 x 43 x 32 mm / 2.6″ x 1.7″ x 1.3″
1 x IR Blaster cable, black, length: 1 m / 3.3 ft
1 x IR Receiver cable, black, length: 1 m / 3.3 ft
1 x Remote control: black
WARRANTY: Lifetime return-to-base
2 years onsite (UK only)
ORDER PART CODE:
Transmitter: TC-HDMIWMTX [SAP: 4432256]
Receiver: TC-HDMIWMRX [SAP: 4432257]