Digital Signage HDMI-over-IP Matrix | Vision Audio Visual

Extenders
HDMI-over-IP

Digital Signage HDMI-over-IP Matrix

  • Transmits HDMI over a network or Point-to-Point
  • Plug-and-Play; no PC necessary for basic setup
  • 4K @ 60Hz (H.264)
  • Supports video walls up to 3x3
  • Share on
  • or

Designed for video transmission applications the Techconnect Matrix allows distribution of HDMI content over an existing LAN infrastructure. You simply need a transmitter for each source, and a receiver for each display.

SETUP NOTE: The first time you connect source PC to Tx, drop refresh rate on PC to establish handshake. Once it is working restore refresh rate.

Features

  • Switch / Distribute / Matrix

    This product uses an IP network to distribute, switch, or matrix. It can have up to 100 x transmitters, and 100 x receivers.

  • Managed Switch

    A “layer-3” switch is required with IGMP snooping turned on to allow multicasting. You don’t need to know what this means, but it is essential it is turned on.

  • Shared Subnet

    All end points must be on the same sub-net.

  • 4Kx2K

    With a maximum transfer rate of 18 Gbps and using H.264 compression this system supports 4K.

  • Point-to-Point

    You can connect a transmitter directly to a receiver with a CAT6 cable and use it as a simple extender. Maximum cable length up to 120 m (394 ft).

  • Scaleable

    Whether you need a small system or a large system; just buy what you need. When your system needs to grow just add more end points. Transmitters and receivers are sold separately.

  • Easy Setup and Switching

    Each transmitter and receiver should be set to a unique channel on the front panel. Adjust the “TX Connected” channel on each receiver to select the target transmitter. Use the buttons on the front panel or the included remote control to change channels.

  • Advanced Software

    Setup software is included for Mac and PCs. It scans for devices and allows the integrator to set device name, channel and IP address.

  • Video Wall Presets

    Supports up to 3x3 video walls. Enter video wall mode and choose from 3x3, 3x2, 3x1, 2x2, 2x3, 1x3. Fine tune with bezel adjustment.

  • IR Passback

    The system supports IR passback so source devices can be controlled remotely. IR emitter and receiver cables are included with each device.

  • Crestron and AMX drivers

    Designing a system controlled by a Crestron or AMX control system is easy.

  • Hot Swap

    If a device needs swapping simply replace it and set the channel on the new device to match the old device. IP and Mac addresses don't need to be modified.

Videos

Specifications

  • PRODUCT DIMENSIONS

    164 x 108.5 x 23.6 mm / 6.46″ x 4.27″ x 0.93 ” (length x width x height)

  • PACKAGED DIMENSIONS

    357 x 153.5 x 85 mm / 14″ x 6.04″ x 3.35 ”

  • PRODUCT WEIGHT

    330g / 0.73 lb

  • PACKAGED WEIGHT

    0.8kg / 1.76 lb

  • CONSTRUCTION MATERIAL

    Metal

  • COLOUR

    Black

  • INPUT AND OUTPUT TMDS SIGNAL

    0.7-1.5 volts p-p

  • INPUT AND OUTPUT DDC SIGNAL

    5 volts p-p (TTL)

  • MAXIMUM VIDEO FORMAT SUPPORTED

    4K

  • OUTPUT VIDEO

    HDMI 2.0 with HDCP 2.2

  • OUTPUT AUDIO

    PCM

  • COMPRESSION

    H.264

  • INPUT AND OUTPUT HDMI CABLE LENGTH

    5m (16.4 ft) AWG 26

  • VIDEO LATENCY

    < 500 Ms

  • SWITCH TIME

    approx 5 seconds (caused by HDCP handshake)

  • OPERATING TEMPERATURE RANGE

    0-50°C

  • STORAGE TEMPERATURE RANGE

    -10-70°C

  • OPERATING HUMIDITY RANGE

    0 to 90 % no condensation

  • REFRESH RATES SUPPORTED

    24, 25, 30, 60Hz

  • TX POWER CONSUMPTION

    7 watts

  • RX POWER CONSUMPTION

    10 watts

  • CAT6 MAXIMUM DISTANCE (IF CONNECTED PEER-TO-PEER DIRECTLY)

    120 m (394 ft)

  • IR PASSBACK BANDWIDTH

    20-60 kHz

  • ESD PROTECTION

    1a Contact discharge level 3 / 1b Air discharge level 3 (Standard: IEC61000-4-2)

  • CONNECTIVITY

    1 x HDMI (type A)
    1 x Ethernet (RJ45)
    1 x DC Power (2-port phoenix)
    1 x 3.5mm Minijack (IR)

  • POWER SUPPLY

    100-240v 50/60Hz AC 5 volt / 3 amp

  • TRANSFORMER INTEGRATED INTO PLUG

  • INCLUDES INTERCHANGEABLE PLUGS

    UK/EU/US/AU

  • DC TAIL LENGTH

    1.8m

  • TRANSFORMER DIMENSIONS

    81 x 52 x 38mm / 3.2″ x 2.05″ x 1.5″

  • ACCESSORIES INCLUDED

    2 x Mounting ears
    1 x Remote Control
    1 x IR Emitter Cable
    1 x IR Receiver Cable

  • WARRANTY

    Lifetime return-to-base

  • COMPLIANCES

    RoHS, WEEE, CE/EMC

  • ORDER PART CODE

    Transmitter TC-MATRIXTX [EU SAP: 4631209 / US SAP: 13293711]
    Receiver TC-MATRIXRX [EU SAP: 4631210 / US SAP: 13293566]

  • ORDER PART CODE

    TC-MATRIX

  • Country of Origin

    China

Where to Buy

Belgium

Czech Republic

Estonia

Finland

Germany

Iceland

Ireland

Italy

Lithuania

Netherlands

Norway

Portugal

South Africa

Spain

Sweden